manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 30 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 30

30

KENR6932

Disassembly and Assembly Section

i02654481

Electronic Unit Injector - Install

 

Installation Procedure

Table 9

Required Tools

Tool

Part

Number

Part Description

Qty

B

27610307

T40 Torx Socket

1

GE50028

Vacuum Pump

1

D

GE50030

Tube

7.9 mm (0.31 inch)

Outside Diameter

1

E

27610294

Injector Pipe Nut Tool

1

F

27610296

Torque Wrench

1

NOTICE

Ensure that all adjustments and repairs that are

carried out to the fuel system are performed by

authorised personnel that have the correct train-

ing.

Before begining ANY work on the fuel system, re-

fer to Operation and Maintenance Manual, “Gen-

eral Hazard Information and High Pressure Fuel

Lines” for safety information.

Refer to Systems Operation, Testing and Adjust-

ing Manual, “Cleanliness of Fuel System Compo-

nents” for detailed information on the standards

of cleanliness that must be observed during ALL

work on the fuel system.

NOTICE

Care must be taken to ensure that

fl

uids are contained

during performance of inspection, maintenance, test-

ing, adjusting and repair of the product. Be prepared to

collect the

fl

uid with suitable containers before open-

ing any compartment or disassembling any compo-

nent containing

fl

uids.

Dispose of all

fl

uids according to local regulations and

mandates.

NOTICE

Use a deep socket in order to remove the electrical

connections from the electronic unit injectors. Use of

incorrect tooling will result in damage to the electronic

unit injectors.

g01341874

Illustration 51

Typical calibration code

1.

If a replacement electronic unit injector is installed,

the correct injector trim

fi

le must be programmed

into the electronic control module. Refer to

Troubleshooting, “Injector Trim File” for more

information. The code that is required to obtain

the injector trim

fi

le is located at position (X).

Note:

Record code (X) before the electronic unit

injector is installed.

2.

Use Tooling (D) in order to remove any fuel from

the cylinder.

Note:

Evacuate as much fuel as possible from the

cylinder before installing the electronic unit injector.

3.

Ensure that the fuel inlet port of the electronic unit

injector is capped. Ensure that the electronic unit

injector is clean.

g01255701

Illustration 52

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов