Perkins 1106C Series Скачать руководство пользователя страница 135

Страница: 135 / 192

KENR6932

135

Disassembly and Assembly Section

i02654412

Engine Oil Pan - Remove

(Aluminum Oil Pan)

Removal Procedure

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

NOTICE

Care must be taken to ensure that

uids are contained

during performance of inspection, maintenance, test-

ing, adjusting and repair of the product. Be prepared to

collect the

uid with suitable containers before open-

ing any compartment or disassembling any compo-

nent containing

uids.

Dispose of all

uids according to local regulations and

mandates.

g01340605

Illustration 276
Typical example

If necessary, remove the assembly of dipstick

tube. Loosen nut (1) and remove tube assembly

(2). remove seal (3) from the tube assembly.

Note:

Identify the position and orientation of the tube

assembly.

g01340606

Illustration 277
Typical example

Place a suitable container below engine oil

pan (7). Remove drain plug (5) and drain the

engine lubricating oil. Refer to Operation and

Maintenance Manual, “Engine Oil and Filter -

Change” for the correct procedure.

Remove O-ring seal (6) from drain plug (5).

Disconnect breather hose from the clip that

secures the hose to the engine oil pan. Position

the breather hose away from the engine oil pan.

Support the assembly of the engine oil pan.

Loosen the long isolating screws (8) and the two

short isolating screws (9). Mark the position of the

clip that secures breather hose . Remove the clip.

Note:

The isolating screws are held captive by joint

(4).

Remove the assembly of the engine oil pan from

the engine.

If necessary, remove the plate for the engine oil

pan. Refer to Disassembly and Assembly, “Engine

Oil Pan Plate - Remove and Install”.

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 135 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: