Perkins 1106C Series Скачать руководство пользователя страница 15

Страница: 15 / 192

KENR6932

Disassembly and Assembly Section

g01335197

Illustration 18

14.

Remove bolts (11) from tube clips (12) that secure

fuel injection line (6). Loosen allen head screws

(13). Position the tube clips in order to allow

removal of the fuel injection line.

15.

Disconnect fuel injection line (6) at fuel injection

pump (7).

16.

Disconnect fuel injection line (6) at fuel manifold

(4).

17.

Plug all open ports immediately. Use Tooling (A)

in order to plug the open ports in fuel manifold (4)

and in fuel injection pump (7).

18.

Remove fuel injection line (6).

19.

Remove allen head screws (13) and tube clips

(12) from fuel injection line (6). Discard the fuel

injection line.

i02654497

Fuel Injection Lines - Install

Installation Procedure

Table 2

Required Tools

Tool

Part Number

Part Name

Qty

27610294

Injector Pipe Nut Tool

NOTICE

Ensure that all adjustments and repairs that are

carried out to the fuel system are performed by

authorised personnel that have the correct train-

ing.

Before begining ANY work on the fuel system, re-

fer to Operation and Maintenance Manual, “Gen-

eral Hazard Information and High Pressure Fuel

Lines” for safety information.

Refer to System Operation, Testing and Adjusting,

“Cleanliness of Fuel System Components” for de-

tailed information on the standards of cleanliness

that must be observed during ALL work on the fu-

el system.

Note:

The following procedure should be adopted

in order to install the fuel injection lines when the

electronic unit injectors or the fuel manifold have

not been removed. If the electronic unit injectors

or the fuel manifold have been removed, refer to

Disassembly and Assembly, “Electronic Unit Injector

- Install” and Disassembly and Assembly, “Fuel

Manifold - Install” for more information.

g01335197

Illustration 19
Assembly of the tube clip

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 15 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: