manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 106 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 106

106

KENR6932

Disassembly and Assembly Section

g01339655

Illustration 203

2.

Remove canister (20) for the breather. Refer to

Operation and maintenance Manual, “Crankcase

Breather (Canister) - Replace”.

3.

Loosen clamp (19) and remove hose (21).

4.

Release two spring clamps (14) in order to remove

hose (15). Remove the hose.

5.

Remove bolts (17). Remove base (18) from the

inlet manifold.

If a spacer is installed between the base and the

inlet manifold, remove spacer (16).

6.

Carefully pry cover (1) from breather body (4).

Note:

Note the orientation of the outlet.

7.

Remove gauze (2) from breather body (4).

8.

Remove O-ring seal (3) from breather body (4).

9.

Use Tooling (A) in order to unscrew breather body

(4) from adapter plate (8).

10.

Remove O-ring seal (5) from breather body (4).

11.

Remove bolts (6) and washers (7) from adapter

plate (8).

12.

Remove adapter plate (8) from valve mechanism

cover (10).

13.

Remove O-ring seal (9) from adapter plate (8).

i02654407

Crankcase Breather - Install

(Un

fi

ltered Breather)

 

Installation Procedure

Table 48

Required Tools

Tool

Part

Number

Part Description

Qty

A

-

Breather Tool

1

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

g01339595

Illustration 204

Breather tool

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов