Perkins 1106C Series Скачать руководство пользователя страница 69

Страница: 69 / 192

KENR6932

Disassembly and Assembly Section

g01336658

Illustration 119

Remove bolts (4).

Note:

The bolts are three different lengths. Note the

positions of the different bolts.

Remove water pump (3) from front cover (1).

Note:

If necessary, tap the water pump with a soft

hammer in order to loosen the water pump.

Remove joint (2).

If necessary, remove cover (6) from the water

pump. Follow Steps 6.a through 6.c in order to

remove the cover.

Remove bolts (7).

Remove cover (6).

Remove joint (5).

i02654551

Water Pump - Install

Installation Procedure

Table 22

Required Tools

Tool

Part

Number

Part Description

Qty

Guide Stud

(M8 by 70 mm)

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

NOTICE

Care must be taken to ensure that

uids are contained

during performance of inspection, maintenance, test-

ing, adjusting and repair of the product. Be prepared to

collect the

uid with suitable containers before open-

ing any compartment or disassembling any compo-

nent containing

uids.

Dispose of all

uids according to local regulations and

mandates.

Ensure that the water pump is clean and free from

wear or damage. If necessary, replace the water

pump.

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 69 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: