Perkins 1106C Series Скачать руководство пользователя страница 167

Страница: 167 / 192

KENR6932

167

Disassembly and Assembly Section

g01341704

Illustration 337

Typical example

Lubricate a new O-ring seal (5) with clean engine

oil. Install the new O-ring seal into the

rst groove

in position sensor (3).

Remove the plug from the hole in the fuel injection

pump for the position sensor.

Align the hole in position sensor (3) with the hole

in the fuel injection pump. Install the position

sensor to the fuel injection pump.

Note:

Do not use bolt (4) to pull the position sensor

into position against the fuel injection pump.

Install bolt (4). Tighten the bolt to a torque of

22 N·m (16 lb ft).

Connect harness assembly (2) to position sensor

(3).

Slide locking tab (1) into the locked position.

i02654460

Coolant Temperature Sensor -

Remove and Install

Removal Procedure

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

NOTICE

Care must be taken to ensure that

uids are contained

during performance of inspection, maintenance, test-

ing, adjusting, and repair of the product. Be prepared

to collect the

uid with suitable containers before

opening any compartment or disassembling any com-

ponent containing

uids.

Dispose of all

uids according to local regulations and

mandates.

Drain the coolant from the cooling system, to a

level below the coolant temperature sensor, into

a suitable container for storage or for disposal.

Refer to Operation and Maintenance Manual,

“Cooling System Coolant - Change” for the correct

draining procedure.

g01341684

Illustration 338

Slide locking tab (1) into the unlocked position.

Disconnect harness assembly (2) from coolant

temperature sensor (3).

Use a deep socket in order to remove coolant

temperature sensor (3) from the cylinder head.

Remove O-ring seal (4) from the coolant

temperature sensor (3).

Installation Procedure

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 167 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: