Perkins 1106C Series Скачать руководство пользователя страница 117

Страница: 117 / 192

KENR6932

117

Disassembly and Assembly Section

Use Tooling (A) to install circlip (5).

Connect plug (6) to harness assembly (4).

Use a deep socket to connect harness (4) to

electronic unit injectors (2). Use Tooling (C) to

tighten connectors (1) to a torque of 2.4 N·m

(21 lb in).

Install a new cable strap (3) to harness

assembly (4).

Note:

Ensure that cable strap to OE speci

cation.

Repeat steps 5.a through 5.g for remaining

harness assemblies (4).

End By:

Install new fuel injection lines. Refer to

Disassembly and Assembly, “Fuel Injection Lines

- Install”.

Install the valve mechanism cover. Refer to

Disassembly and Assembly, “Valve Mechanism

Cover - Remove and Install”.

i02654541

Rocker Shaft and Pushrod -

Remove

Removal Procedure

Start By:

Remove the valve mechanism cover. Refer to

Disassembly and Assembly, “Valve Mechanism

Cover - Remove and Install”.

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

g01340040

Illustration 230

g01340041

Illustration 231

Progressively loosen torx screws (1). Begin at

the ends of the rocker shaft assembly and work

toward the center.

Note:

To avoid distortion of rocker shaft assembly

(2), each torx screw should be loosened by half a

turn at one time. Repeat the procedure until all torx

screws are loosened.

Remove torx screws (1) from rocker shaft

assembly (2).

Remove rocker shaft assembly (2) from the

cylinder head.

Place an identi

cation mark on pushrods (3) in

order to show the location. Remove the pushrods

from the cylinder head.

Note:

Identi

cation will ensure that the pushrods

can be reinstalled in the original positions. Do not

interchange the positions of used pushrods.

Make a temporary mark on valve bridges (4) in

order to show the location and the orientation.

Remove the valve bridges from the cylinder head.

Note:

Identi

cation will ensure that the valve bridges

can be reinstalled in the original location and the

original orientation. Do not interchange the location

or the orientation of used valve bridges.

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 117 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: