manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 156 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 156

156

KENR6932

Disassembly and Assembly Section

Installation Procedure

Table 75

Required Tools

Tool

Part

Number

Part Name

Qty

B

21825607

Angle Gauge

1

21825496

Dial Gauge

1

B

-

Magnetic Base

1

NOTICE

This procedure must only be used to remove and in-

stall the main bearing shells with the crankshaft in po-

sition.

The removal procedure and the installation procedure

must be completed for each pair of main bearing shells

before the next pair of main bearing shells are re-

moved.

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

1.

Ensure that the main bearing shells are clean and

free from wear or damage. If necessary, replace

the main bearing shells.

2.

Clean the journals of the crankshaft. Inspect

the journals of the crankshaft for damage. If

necessary, replace the crankshaft or recondition

the crankshaft.

g01341335

Illustration 313

3.

Lubricate the crankshaft journal and upper main

bearing shell (5) with clean engine oil. Slide upper

main bearing shell (5) into position between the

crankshaft journal and the cylinder block. Ensure

that the locating tab for the upper main bearing

shell is correctly seated in the slot in the cylinder

block.

Note:

The upper main bearing shell has a groove

and two oil holes.

g01341325

Illustration 314

4.

For number six main bearing, ensure that two

thrust washers (4) are clean and free from wear or

damage. If necessary, replace the thrust washers.

Lubricate thrust washers (4) with clean engine

oil. Slide thrust washers (4) into position between

the crankshaft and the cylinder block. Ensure that

the locating tab is correctly seated in the cylinder

block.

g01341324

Illustration 315

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов