manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 18 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 18

18

KENR6932

Disassembly and Assembly Section

g01335253

Illustration 23
Typical example

g01335254

Illustration 24

Typical example

6.

Place a suitable container below fuel injection

pump (1) in order to catch any fuel that might be

spilled.

7.

Disconnect plastic tube assembly (2) from fuel

injection pump (1).

8.

Disconnect harness assembly (7) from solenoid

(3) of the fuel injection pump. Disconnect engine

wiring harness (7) from position sensor (4) for the

fuel injection pump.

Note:

The harness assembly should be positioned

in order to avoid an obstruction to the fuel injection

pump.

9.

Remove plastic tube assembly (11) from fuel

transfer pump (8).

10.

Disconnect plastic tube assembly (10) from the

outlet of fuel transfer pump (8).

11.

Disconnect plastic tube assembly (5) from fuel

injection pump (1).

12.

Remove tube assembly (12) for the fuel return

from the fuel transfer pump and the cylinder head.

Note:

Disconnect the tube assembly at the fuel

transfer pump

fi

rst in order to drain the fuel from the

cylinder head.

13.

Remove tube assembly (9) for the engine oil

supply to fuel injection pump (1).

14.

Plug or cap all open ports and tube assemblies

immediately with new plugs or caps.

15.

Remove fuel injection line (6) that connects the

fuel injection pump to the fuel manifold. Refer to

Disassembly and Assembly, “Fuel Injection Lines

- Remove”. Use Tooling (D) in order to plug the

open ports in the fuel injection pump and in the

fuel manifold. Discard the fuel injection line.

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов