Perkins 1106C Series Скачать руководство пользователя страница 118

Страница: 118 / 192

118

KENR6932

Disassembly and Assembly Section

i02654539

Rocker Shaft - Disassemble

Disassembly Procedure

Start By:

Remove the rocker shaft assembly. Refer to

Disassembly and Assembly, “Rocker Shaft and

Pushrod - Remove”.

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

Personal injury can result from being struck by

parts propelled by a released spring force.

Make sure to wear all necessary protective equip-

ment.

Follow the recommended procedure and use all

recommended tooling to release the spring force.

Make an identi

cation mark on each rocker arm

assembly in order to show the location.

Note:

The components must be reinstalled in the

original location. Do not interchange components.

g01340047

Illustration 232

Remove pedestals (1) from rocker shaft (5). It is

not necessary to remove locators (2) from the

pedestals.

Remove rocker arm assembly (4) for the exhaust

valve from rocker shaft (5). Remove rocker arm

assembly (3) for the inlet valve from rocker shaft

(5). Begin at the rear of the rocker shaft assembly.

Note:

The rocker arm assembly for the inlet valve is

longer than the rocker arm assembly for the exhaust

valve.

Remove spring (6) from rocker shaft (5).

Repeat Steps 3 and 4 in order to remove the

remaining rocker arms from rocker shaft (5).

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 118 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: