manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 5 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 5

KENR6932

5

Disassembly and Assembly Section

Disassembly and Assembly

Section

i02654356

Fuel Priming Pump - Remove

and Install

(Mechanical Priming Pump)

 

Removal Procedure

NOTICE

Ensure that all adjustments and repairs that are

carried out to the fuel system are performed by

authorised personnel that have the correct train-

ing.

Before begining ANY work on the fuel system, re-

fer to Operation and Maintenance Manual, “Gen-

eral Hazard Information and High Pressure Fuel

Lines” for safety information.

Refer to System Operation, Testing and Adjusting,

“Cleanliness of Fuel System Components” for de-

tailed information on the standards of cleanliness

that must be observed during ALL work on the fu-

el system.

1.

Isolate the fuel supply.

2.

Make a temporary identi

fi

cation mark on plastic

tube assemblies (1) in order to show the correct

position of the tube assemblies.

3.

Place a suitable container below the fuel priming

pump in order to catch any fuel that might

be spilled. Drain the primary

fi

lter (7). Refer

to Operation and Maintenance Manual, “Fuel

System Primary Filter (Water Seperator) Element

- Replace”.

g01334872

Illustration 1

Typical example

4.

Disconnect plastic tube assemblies (1). Plug

the tube assemblies with new plugs. Cap open

connectors (2) on the fuel priming pump with new

caps.

5.

Remove primary

fi

lter (6) from fuel priming pump

(4). Refer to Operation and Maintenance, “Fuel

System Primary Filter (Water Seperator) Element

- Replace”.

6.

Remove bolts (7) from fuel priming pump (4).

Remove fuel priming pump (4) from the mounting

bracket.

7.

If necessary, follow Steps 7.a through 7.c in order

to disassemble fuel priming pump (4).

a.

Remove connectors (2) from fuel priming pump

(4).

b.

Remove plugs (5) from fuel priming pump (4).

c.

Remove O-ring seals (3) from connectors (2)

and plugs (5).

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов