Perkins 1106C Series Скачать руководство пользователя страница 68

Страница: 68 / 192

KENR6932

Disassembly and Assembly Section

g01336651

Illustration 118

If necessary, lubricate the internal components for

the assembly of the engine oil pump with clean

engine oil. Install outer rotor (8) and front cover

(7) to the housing of engine oil pump (4). Install

the allen head screws (9). Tighten the allen head

screws to a torque of 22 N·m (16 lb ft).

Ensure that two dowels (10) and (11)are correctly

located in the housing of engine oil pump (4).

Position the assembly of the engine oil pump onto

the cylinder block.

Note:

Ensure that the dowels in the housing of the

engine oil pump are aligned with the holes in the

cylinder block.

Install bolts (5). Tighten the bolts to a torque of

44 N·m (32 lb ft).

Check the backlash between idler gear (12) and

the crankshaft gear. Refer to Speci

cations, “Gear

Group (Front)” for further information.

Install suction pipe (2) and a new joint to the

assembly of the engine oil pump.

Install bolts (1). Tighten the bolts to a torque to

22 N·m (16 lb ft).

If the suction pipe has a support bracket follow

Steps 9.a through 9.c.

Install the components of the support bracket.

Ensure the correct location and orientation of

the bracket and the retaining clip.

Tighten the bolts

nger tight in order to align

the components of the support bracket.

Tighten bolts (1) to a torque of 22 N·m (16 lb ft).

End By:

Install the engine oil pan. Refer to Disassembly

and Assembly, “Engine Oil Pan - Install”.

i02654553

Water Pump - Remove

Removal Procedure

Start By:

Remove the fan and the fan pulley. Refer to

Disassembly and Assembly, “Fan - Remove and

Install”.

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

NOTICE

Care must be taken to ensure that

uids are contained

during performance of inspection, maintenance, test-

ing, adjusting and repair of the product. Be prepared to

collect the

uid with suitable containers before open-

ing any compartment or disassembling any compo-

nent containing

uids.

Dispose of all

uids according to local regulations and

mandates.

Drain the coolant from the cooling system into

a suitable container for storage or disposal.

Refer to Operation and Maintenance Manual,

“Cooling System Coolant - Change” for the correct

procedure.

Loosen the hose clamps and remove the hose

from the water pump inlet.

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 68 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: