manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 55 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 55

KENR6932

55

Disassembly and Assembly Section

g01335985

Illustration 93

Typical example

4.

Install Tooling (A) in position on the cylinder head

in order to compress appropriate valve spring (3).

NOTICE

Ensure that the valve spring is compressed squarely

or damage to the valve stem may occur.

5.

Apply suf

fi

cient pressure to Tooling (A) in order to

remove valve keepers (1).

Note:

Do not compress the spring so that valve

spring retainer (2) touches valve stem seal (4).

6.

Slowly release pressure on Tooling (A).

g01335986

Illustration 94

7.

Remove valve spring retainer (2). Remove valve

spring (3).

8.

Repeat steps 4 to 7 for the remaining valves.

9.

Remove Tooling (A).

10.

Remove valve stem seals (4).

11.

Use a suitable lifting device to carefully turn over

the cylinder head.

12.

Remove valves (5).

Installation Procedure

Table 19

Required Tools

Tool

Part Number

Part Description

Qty

21825666

Valve Spring

Compressor

1

27610235

Adapter

1

A

27610295

Head

1

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

1.

Clean all components of the cylinder head

assembly. Ensure that all ports, all coolant

passages and all lubrication passages in the

cylinder head are free from debris. Follow Steps

1.a through 1.d in order to inspect the components

of the cylinder head assembly. Replace any

components that are worn or damaged.

a.

Inspect the cylinder head for wear and for

damage. Refer to System Operation, Testing

and Adjusting, “Cylinder Head Inspect”.

b.

Inspect the valve seats for wear and for

damage. Refer to Speci

fi

cations, “Cylinder

Head Valves” for further information.

c.

Inspect the valve guides for wear and for

damage. Refer to Speci

fi

cations, “Cylinder

Head Valves” and System Operation, Testing

and Adjusting, “Valve Guide - Inspect” for

further information.

d.

Inspect the valves for wear and for damage.

Refer to Speci

fi

cations, “Cylinder Head Valves

”.

e.

Inspect valve springs (3) for damage and for

the correct length. Refer to Speci

fi

cations,

“Cylinder Head Valves ”.

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов