Perkins 1106C Series Скачать руководство пользователя страница 140

Страница: 140 / 192

140

KENR6932

Disassembly and Assembly Section

g01340605

Illustration 284

13.

If necessary, follow Steps 13 through 13.c in order

to install the assembly of the dipstick tube.

Install a new seal (3) to tube assembly (2).

Apply Tooling (D) to nut (1). Install the tube

assembly to the engine oil pan.

Note:

Ensure that the orientation of the tube

assembly is correct.

Tighten the nut to a torque of 18 N·m (13 lb ft).

Install the dipstick.

Note:

After the engine has been installed, ensure that

the engine oil pan is

lled with lubricating oil to the

correct level. Refer to Operation and Maintenance

Manual, “Oil Filter Change” for the correct procedure.

i02654409

Engine Oil Pan - Install

(Aluminum Oil Pan)

Installation Procedure

Table 63

Required Tools

Tool

Part

Number

Part Description

Qty

Guide Stud
(M8 by 100 mm)

21820117

POWERPART

Threadlock and Nutlock

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

NOTICE

Care must be taken to ensure that

uids are contained

during performance of inspection, maintenance, test-

ing, adjusting and repair of the product. Be prepared to

collect the

uid with suitable containers before open-

ing any compartment or disassembling any compo-

nent containing

uids.

Dispose of all

uids according to local regulations and

mandates.

If necessary, install the plate for the engine oil

pan. Refer to Disassembly and Assembly, “Engine

Oil Pan Plate - Remove and Install”.

g01340664

Illustration 285
Typical example

Install Tooling (A) to positions (X) in the cylinder

block.

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 140 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: