manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 40 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 40

40

KENR6932

Disassembly and Assembly Section

g01335754

Illustration 70

15.

Install exhaust manifold (1) and the assembly of

the turbocharger to the cylinder head. Refer to

Disassembly and Assembly, “Exhaust Manifold -

Remove and Install” for the correct procedure.

16.

Install bolt (8)

fi

nger tight. Ensure that tube

assembly (7)

fi

ts correctly.

17.

Position a new joint (3) between the

fl

ange of

tube assembly (4) and the cylinder block. Install

bolts (5)

fi

nger tight.

18.

If a new turbocharger has been installed, check

that the orientation of bearing housing (18) is

correct. If the orientation of the bearing housing is

not correct, rotate the bearing housing until tube

assemblies (4) and (7)

fi

t correctly. Tighten band

clamps (21) to a torque of 13 N·m (9.6 lb ft).

19.

Tighten banjo bolt (9) to a torque of 20 N·m

(14 lb ft). Tighten bolt (5) and (8) to a torque of

22 N·m (16 lb ft).

20.

Install the bolts for tube clips (2) to the cylinder

block. Tighten bolt (2) to a torque of 44 N·m

(32 lb ft).

21.

If the turbocharger has an exhaust elbow, install

the exhaust elbow. Refer to Disassembly and

Assembly, “Exhaust Elbow - Remove and Install”.

22.

Connect the exhaust pipe.

23.

If the turbocharger has a remote wastegate

solenoid, connect the hose for the solenoid to the

turbocharger.

24.

Connect the air inlet hose and connect the air

outlet hose to the turbocharger.

i02654361

Turbocharger - Install

(Side Mounted Turbocharger)

 

Installation Procedure

Table 12

Required Tools

Tool

Part

Number

Part Description

Qty

A

21820221

POWERPART

Rubber Grease

1

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

g01335496

Illustration 71

Typical example

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов