Perkins 1106C Series Скачать руководство пользователя страница 191

Страница: 191 / 192

KENR6932

191

Index Section

Gear Group (Front) - Remove and Install.............. 89

Installation Procedure ........................................ 91

Removal Procedure ........................................... 89

Glow Plugs - Remove and Install ........................ 172

Installation Procedure ...................................... 172

Removal Procedure ......................................... 172

Housing (Front) - Install ......................................... 99

Installation Procedure ........................................ 99

Housing (Front) - Remove ..................................... 98

Removal Procedure ........................................... 98

Idler Gear - Install .................................................. 95

Installation Procedure (Heavy-Duty Idler Gear).. 96

Installation Procedure (Standard Idler Gear) ..... 95

Idler Gear - Remove .............................................. 92

Removal Procedure (Heavy-Duty Idler Gear) .... 94

Removal Procedure (Standard Idler Gear) ........ 92

Important Safety Information ................................... 2

Inlet Air Temperature Sensor - Remove and

Install ................................................................. 171

Installation Procedure ...................................... 171

Removal Procedure ......................................... 171

Inlet and Exhaust Valve Springs - Remove and

Install ................................................................... 50

Installation Procedure ........................................ 52

Removal Procedure ........................................... 50

Inlet and Exhaust Valves - Remove and Install ..... 54

Installation Procedure ........................................ 55

Removal Procedure ........................................... 54

Inlet Manifold - Remove and Install ....................... 48

Installation Procedure ........................................ 49

Removal Procedure ........................................... 48

Lifter Group - Remove and Install........................ 128

Installation Procedure ...................................... 128

Removal Procedure ......................................... 128

Piston Cooling Jets - Remove and Install............ 145

Installation Procedure ...................................... 146

Removal Procedure ......................................... 145

Pistons and Connecting Rods - Assemble .......... 149

Assembly Procedure........................................ 149

Pistons and Connecting Rods - Disassemble ..... 147

Disassembly Procedure ................................... 147

Pistons and Connecting Rods - Install................. 150

Installation Procedure ...................................... 150

Pistons and Connecting Rods - Remove............. 146

Removal Procedure ......................................... 146

Position Sensor (Fuel Injection Pump) - Remove and

Install ................................................................. 166

Installation Procedure ...................................... 166

Removal Procedure ......................................... 166

Rocker Shaft - Assemble...................................... 119

Assembly Procedure......................................... 119

Rocker Shaft - Disassemble ................................. 118

Disassembly Procedure .................................... 118

Rocker Shaft and Pushrod - Install...................... 120

Installation Procedure ...................................... 120

Rocker Shaft and Pushrod - Remove................... 117

Removal Procedure .......................................... 117

Table of Contents..................................................... 3

Turbocharger - Assemble ...................................... 37

Assembly Procedure.......................................... 37

Turbocharger - Disassemble ................................. 37

Disassembly Procedure ..................................... 37

Turbocharger - Install (Side Mounted

Turbocharger) ...................................................... 40

Installation Procedure ........................................ 40

Turbocharger - Install (Turbocharger Top

Mounted).............................................................. 38

Installation Procedure ........................................ 38

Turbocharger - Remove (Side Mounted

Turbocharger) ...................................................... 36

Removal Procedure ........................................... 36

Turbocharger - Remove (Turbocharger Top Mounted

)............................................................................ 34

Removal Procedure ........................................... 34

Valve Mechanism Cover - Remove and Install..... 110

Installation Procedure ....................................... 111

Removal Procedure .......................................... 110

Valve Mechanism Cover - Remove and Install

(Composite Valve Mechanism Cover) ............... 109

Installation Procedure ....................................... 110

Removal Procedure ......................................... 109

Valve Mechanism Cover Base - Remove and

Install .................................................................. 114

Installation Procedure ....................................... 116

Removal Procedure .......................................... 114

Valve Mechanism Cover Base - Remove and Install

(Composite Valve Mechanism Cover Base) ....... 112

Installation Procedure ....................................... 113

Removal Procedure .......................................... 112

Vibration Damper and Pulley - Install (Pulley with

Split Lock Rings).................................................. 86

Installation Procedure ........................................ 86

Vibration Damper and Pulley - Install (Pulleys without

Split Lock Rings).................................................. 85

Installation Procedure ........................................ 85

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 191 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: