Perkins 1106C Series Скачать руководство пользователя страница 46

Страница: 46 / 192

KENR6932

Disassembly and Assembly Section

g01335809

Illustration 80

g01335810

Illustration 81

Loosen bolts (4) and (6) in reverse numerical

order. Refer to Illustration 81.

Note:

This will help prevent distortion of the exhaust

manifold.

Remove center bolts (4) from exhaust manifold

(3). Remove outer bolts (6) and spacers (5) from

exhaust manifold (3).

Note:

Support the manifold as the bolts are removed.

Remove the assembly of exhaust manifold (3)

and turbocharger.

Remove exhaust manifold gaskets (1).

Remove the turbocharger from exhaust manifold

(3). Refer to Disassembly and Assembly,

“Turbocharger - Remove” Steps 8 through 15.

If necessary, remove studs (2) from exhaust

manifold (3).

Installation Procedure (Top
Mounted Exhaust Manifold)

Table 14

Required Tools

Tool

Part

Number

Part Description

Qty

Guide Stud

(M10 by 100 mm)

21820117

Loctite 575

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 46 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: