Perkins 1106C Series Скачать руководство пользователя страница 41

Страница: 41 / 192

KENR6932

Disassembly and Assembly Section

Ensure that the turbocharger is clean and free

from damage. Inspect the turbocharger for wear.

Refer to System Operation, Testing and Adjusting,

“Turbocharger Inspect” for more information. If

any part of the turbocharger is worn or damaged,

the complete turbocharger must be replaced.

Test the wastegate actuator (19) for correct

operation. Refer to System Operation, Testing and

Adjusting, “Turbocharger Inspect”. If the wastegate

actuator is damaged or the wastegate actuator

does not operate within the speci

ed limits, the

wastegate actuator must be replaced. Refer to

Disassembly and Assembly, “Turbocharger -

Dissassemble” and refer to Disassembly and

Assembly, “Turbocharger - Assemble” for more

information.

g01335456

Illustration 72
Typical example

Clean the mating surfaces of exhaust manifold

(12). If necessary, install studs (13) to the exhaust

manifold. Tighten the studs to a torque of 18 N·m

(13 lb ft).

Install a new joint (14) to exhaust manifold (12).

Position turbocharger (6) on the exhaust manifold.

Note:

Ensure that the turbocharger is correctly

oriented.

Install nuts (15). Tighten the nuts to a torque of

44 N·m (32 lb ft).

If a new turbocharger is installed, bearing housing

(18) and compressor housing (20) must be

oriented to the correct positions. Follow Steps 7.a

through 7.d in order to orient the bearing housing

and the compressor housing.

Loosen band clamps (21) suf

ciently in order

to allow the housings to rotate.

Note:

If the band clamps are damaged, replace the

band clamps.

Carefully turn bearing housing (18) until the

port for oil feed (17) is upward.

Rotate compressor housing (20) until the

compressor outlet is in the correct position.

Refer to the turbocharger that was originally

installed for the correct orientation.

Ensure that band clamps (21) are correctly

oriented. Refer to the turbocharger that was

originally installed for the correct orientation.

Tighten the band clamps

nger tight.

g01335455

Illustration 73

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 41 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: