Perkins 1106C Series Скачать руководство пользователя страница 133

Страница: 133 / 192

KENR6932

133

Disassembly and Assembly Section

g01340534

Illustration 270

g01340551

Illustration 271
Alignment of timing marks

Align the keyway in camshaft gear (1) with the key

in the camshaft. Install camshaft gear onto the

camshaft. Ensure that the timing marks on gears

(1) and (8) are in alignment and that the mesh of

the gears is correct. Refer to Illustration 271.

g01340554

Illustration 272

Install Tooling (B) through hole (X) in the camshaft

gear into the front housing. Install washer (2) and

bolt (3) to camshaft gear (1).

Remove Tooling (B) and (C). Install plug (4) into

hole (Y) in the cylinder block. Refer to Illustration

269.

Tighten bolt (3) to a torque of 95 N·m (70 lb ft).

g01335426

Illustration 273

Ensure that the backlash for gears (1) and (8) is

within speci

ed values. Refer to Speci

cations,

“Gear Group (Front)” for further information.

10.

Ensure that the end play for camshaft gear (1) is

within speci

ed values. Refer to Speci

cations,

“Camshaft” for further information.

11.

Lubricate the teeth of the gears with clean engine

oil.

12.

Adjust the valve lash. Refer to System Operation,

Testing and Adjusting, “Engine Valve Lash -

Inspect/Adjust”.

End By:

Install the front cover. Refer to Disassembly and

Assembly, “Front Cover - Remove and Install”.

Install the valve mechanism cover. Refer to

Disassembly and Assembly, “Valve Mechanism

Cover - Remove and Install”.

i02654456

Camshaft Bearings - Remove

and Install

Removal Procedure

Table 60

Required Tools

Tool

Part

Number

Part Description

Qty

Bearing Puller

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 133 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: