Perkins 1106C Series Скачать руководство пользователя страница 168

Страница: 168 / 192

168

KENR6932

Disassembly and Assembly Section

g01341684

Illustration 339

Lubricate a new O-ring seal (4) with clean engine

oil. Install the new O-ring seal onto coolant

temperature sensor (3).

Use a deep socket in order to install coolant

temperature sensor (3) to the cylinder head.

Tighten the coolant temperature sensor to a

torque of 15 N·m (11 lb ft).

Connect harness assembly (2) to coolant

temperature sensor (3).

Slide locking tab (1) into the locked position.

Fill the cooling system to the correct level. Refer

to Operation and Maintenance Manual, “Cooling

System Coolant Level - Check” and refer to

Operation and Maintenance Manual, “Cooling

System Coolant - Test/Add” for the correct

lling

procedure.

i02654485

Engine Oil Pressure Sensor -

Remove and Install

Removal Procedure

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

NOTICE

Care must be taken to ensure that

uids are contained

during performance of inspection, maintenance, test-

ing, adjusting, and repair of the product. Be prepared

to collect the

uid with suitable containers before

opening any compartment or disassembling any com-

ponent containing

uids.

Dispose of all

uids according to local regulations and

mandates.

g01341698

Illustration 340

Slide locking tab (1) into the unlocked position.

Disconnect harness assembly (2) from engine oil

pressure sensor (3).

Use a deep socket to remove engine oil pressure

sensor (3) from the cylinder block.

Remove O-ring seal (4) from engine oil pressure

sensor (3).

Installation Procedure

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 168 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: