Perkins 1106C Series Скачать руководство пользователя страница 81

Страница: 81 / 192

KENR6932

Disassembly and Assembly Section

g01337563

Illustration 142

Typical example

Install a suitable lifting device to the

ywheel

housing. The

ywheel housing can weigh 32 kg

(70.5 lb).

Use the lifting device to align

ywheel housing (1)

with Tooling (A). Install the

ywheel housing to the

cylinder block.

Install bolts (2) and bolts (3).

Remove Tooling (A). Install remaining bolts (3).

10.

Tighten bolts (3) to a torque of 63 N·m (46 lb ft).

11.

Tighten bolts (2) to a torque of 78 N·m (57.5 lb ft).

12.

Check the alignment of

ywheel housing (1) with

the crankshaft. Refer to System Operation, Testing

and Adjusting, “Flywheel Housing - Inspect”.

End By:

Install the

ywheel. Refer to Disassembly and

Assembly, “Flywheel - Install”.

i02654369

Flywheel Housing - Remove

and Install

(Wet Back End Housing)

Removal Procedure

Start By:

Remove the

ywheel. Refer to Disassembly and

Assembly, “Flywheel - Remove”.

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

Install a suitable lifting device to the

ywheel

housing in order to support the

ywheel housing.

The

ywheel housing can weigh 32 kg (70.5 lb).

g01337602

Illustration 143
Typical example

Remove bolts (2). Remove bolts (4). Remove

bolts (3) from

ywheel housing (1).

Use the lifting device in order to remove

ywheel

housing (1) from the cylinder block.

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 81 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: