manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 67 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 67

KENR6932

67

Disassembly and Assembly Section

g01336647

Illustration 115

Typical example

2.

Remove the bolts (1) and suction pipe (2).

3.

Remove the joint from the suction pipe.

4.

Remove bolts (5). Remove the assembly of engine

oil pump (4) from the cylinder block.

5.

If necessary, remove pressure relief valve (3)

from the housing of engine oil pump (4). Refer to

Disassembly and Assembly, “Engine Oil Relief

Valve - Remove and Install”.

g01336648

Illustration 116
Typical example

6.

If necessary, remove allen head screws (9) and

front cover assembly (7). Remove outer rotor (8)

from the housing of the engine oil pump.

Note:

Do not remove dowels (9) or (11)from the

housing of the engine oil pump unless the dowels

are damaged.

i02654486

Engine Oil Pump - Install

 

Installation Procedure

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

NOTICE

If any part of the engine oil pump is worn or damaged,

the complete assembly of the engine oil pump must

be replaced.

1.

Ensure that all components of the engine oil pump

are clean and free from wear or damage. Refer to

System Operation, Testing and Adjusting, “Engine

Oil Pump - Inspect” for more information. Replace

the complete assembly of the engine oil pump if

any of the components are worn or damaged.

g01336647

Illustration 117
Typical example

2.

If necessary, install the pressure relief valve (3).

Refer to Disassembly and Assembly, “Engine

Oil Relief Valve - Remove and Install” for further

information.

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов