Perkins 1106C Series Скачать руководство пользователя страница 78

Страница: 78 / 192

KENR6932

Disassembly and Assembly Section

g01374593

Illustration 135

Typical example

Ensure that crankshaft

ange (1) is clean, dry and

free from damage.

Ensure that the mating surface of the cylinder

block is clean and dry.

Ensure that plastic sleeve (3) is squarely installed

within new crankshaft rear seal (2).

Note:

The plastic sleeve is included in order to

protect the lip of the seal as the crankshaft rear seal

is pushed over crankshaft

ange (1). Do not attempt

to install a crankshaft rear seal without the plastic

sleeve.

g01337517

Illustration 136

Typical example

Place the assembly of the crankshaft rear seal

over crankshaft

ange (1). Align dowel (5) with the

slot in the crankshaft rear seal.

Ensure that plastic sleeve (3) is engaged on

crankshaft

ange (1). Push crankshaft rear seal

(2) squarely onto the crankshaft. Ensure that the

crankshaft rear seal is seated against the cylinder

block. During this process, plastic sleeve (3) will

be forced out of the crankshaft rear seal. Discard

the plastic sleeve.

Note:

Ensure that dowel (5) is engaged in the hole in

the crankshaft rear seal.

Install Tooling (C) to the cylinder block and to

crankshaft rear seal (2). Tighten the bolts to a

torque of 15 N·m (11 lb ft).

Use Tooling (B) in order to install two Torx bolts (4)

to crankshaft rear seal (3) in position (X). Tighten

two Torx bolts (4) to a torque of 22 N·m (16 lb ft).

Use Tooling (B) in order to install remaining Torx

bolts (4). Tighten all Torx bolts (4) to a torque of

22 N·m (16 lb ft).

10.

Remove Tooling (C).

End By:

Install the engine oil pan plate. Refer to

Disassembly and Assembly, “Engine Oil Pan Plate

- Remove and Install”.

i02654494

Flywheel Housing - Remove

and Install

(Standard Housing)

Removal Procedure

Table 28

Required Tools

Tool

Part

Number

Part Description

Qty

Guide Stud
(M10 by 100 mm)

Start By:

Remove the

ywheel. Refer to Disassembly and

Assembly, “Flywheel - Remove”.

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 78 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: