manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 84 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 84

84

KENR6932

Disassembly and Assembly Section

i02654373

Vibration Damper and Pulley -

Remove

(Pulleys without Split Lock

Rings)

 

Removal Procedure

Table 31

Required Tools

Tool

Part

Number

Part Description

Qty

A

-

Guide Stud

(M12 by 70 mm)

1

B

27610299

E18 Torx socket

1

Start By:

a.

Remove the alternator belt. Refer to Disassembly

and Assembly, “Alternator Belt - Remove and

Install”.

Note:

The weight of the assembly of the crankshaft

pulley, the vibration damper and the crankshaft

adapter is approximately 22 kg (48 lb). Remove the

vibration damper and the crankshaft pulley before the

crankshaft adapter is removed from the engine.

g01337793

Illustration 150

1.

Remove one of bolts (4). Install Tooling (A) into the

assembly of the crankshaft pulley, the vibration

damper and the crankshaft adapter.

2.

Remove remaining bolts (4).

3.

Remove vibration damper (3) and crankshaft

pulley (2) from crankshaft adapter (1). Remove

Tooling (A) from crankshaft adapter (1).

4.

Use a suitable tool in order to prevent the

crankshaft from rotating. Use Tooling (B) to

remove torx screws (5).

5.

Remove the crankshaft adapter (1) from the

crankshaft.

i02654372

Vibration Damper and Pulley -

Remove

(Pulley with Split Lock Rings)

 

Removal Procedure

Table 32

Required Tools

Tool

Part

Number

Part Description

Qty

A

-

Guide Stud
(M12 by 70 mm)

1

B

27610299

E18 Torx socket

1

Start By:

a.

Remove the Alternator belt. Refer to Disassembly

and Assembly, “Alternator Belt - Remove and

Install”.

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

Note:

The weight of the assembly of the crankshaft

pulley, the vibration damper and the crankshaft

adapter is approximately 22 kg (48 lb). Remove the

vibration damper and the crankshaft pulley before the

crankshaft adapter is removed from the engine.

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов