Perkins 1106C Series Скачать руководство пользователя страница 71

Страница: 71 / 192

KENR6932

Disassembly and Assembly Section

g01336661

Illustration 122

Tighten bolts (4) and (7) in the sequence that is

shown in Illustration 122 to a torque of 22 N·m

(16 lb ft).

10.

Install the hose to the water pump inlet. Tighten

the hose clamps.

11.

Fill the cooling system with coolant. Refer to

Operation and Maintenance Manual, “Cooling

System Coolant - Change” for the correct

procedure.

End By:

Install the fan and the fan pulley. Refer to

Disassembly and Assembly, “Fan - Remove and

Install”.

i02654555

Water Temperature Regulator -

Remove and Install

Removal Procedure

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

NOTICE

Care must be taken to ensure that

uids are contained

during performance of inspection, maintenance, test-

ing, adjusting and repair of the product. Be prepared to

collect the

uid with suitable containers before open-

ing any compartment or disassembling any compo-

nent containing

uids.

Dispose of all

uids according to local regulations and

mandates.

Drain the coolant from the cooling system to a

level below the water temperature regulator, into

a suitable container for storage or for disposal.

Refer to Operation and Maintenance Manual,

“Cooling System Coolant - Change” for the correct

draining procedure.

Loosen the hose clamps from the upper radiator

hose and disconnect the upper radiator hose from

water temperature regulator housing (2).

g01336665

Illustration 123

Typical example

Remove bolts (1) from water temperature

regulator housing (2).

Remove water temperature regulator housing (2)

from the cylinder head.

Note:

Note the orientation of the water temperature

regulator housing.

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 71 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: