manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 88 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 88

88

KENR6932

Disassembly and Assembly Section

g01337799

Illustration 155
Typical example

2.

Assemble Tooling (B).

3.

Align new crankshaft front seal (1) to the front

housing.

Note:

If the crankshaft front seal is supplied with a

sleeve, remove the sleeve from the crankshaft front

seal before installation.

4.

Use Tooling (B) to install crankshaft front seal (1).

Ensure that the front face of the seal is installed to

a depth of 6.5 ± 0.2 mm (0.256 ± 0.008 inch) into

the front housing.

5.

Remove Tooling (B) from the crankshaft.

End By:

a.

Install the crankshaft pulley. Refer to Disassembly

and Assembly, “Crankshaft Pulley - Remove and

Install”.

i02654495

Front Cover - Remove and

Install

 

Removal Procedure

Start By:

a.

If the engine has a fan, remove the fan. Refer to

Disassembly and Assembly, “Fan - Remove and

Install”.

b.

Remove the water pump. Refer to Disassembly

and Assembly, “Water Pump - Remove”.

Note:

In order to remove the front cover, it is not

necessary to remove the crankshaft pulley or the

alternator.

g01337873

Illustration 156

Typical example

1.

Remove bolts (3) and (4). Remove bolt (5). Identify

the positions of the different bolts .

Note:

The bolt (5) may not be installed to some

engines.

2.

Remove front cover (1) from the front housing.

3.

Remove joint (2) from front cover (1).

Installation Procedure

Table 37

Required Tools

Tool

Part

Number

Part Name

Qty

A

-

Guide Stud

(M8 by 70 mm)

2

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов