manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 169 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 169

KENR6932

169

Disassembly and Assembly Section

g01341698

Illustration 341

1.

Lubricate a new O-ring seal (4) with clean engine

oil. Install the new O-ring seal onto engine oil

pressure sensor (3).

2.

Use a deep socket to install engine oil pressure

sensor (3) to the cylinder block. Tighten the engine

oil pressure sensor to a torque of 10 N·m (89 lb in).

3.

Connect harness assembly (2) to engine oil

pressure sensor (3).

4.

Slide locking tab (1) into the locked position.

5.

If necessary,

fi

ll the engine oil pan to the correct

level that is indicated on the engine oil level

gauge. Refer to Operation and Maintenance

Manual, “Engine Oil Level - Check”.

i02654511

Fuel Pressure Sensor -

Remove and Install

 

Removal Procedure

Table 80

Required Tools

Tool

Part

Number

Part Name

Qty

A

-

Seal Pick

1

Contact with high pressure fuel may cause

fl

uid

penetration and burn hazards. High pressure fu-

el spray may cause a

fi

re hazard. Failure to fol-

low these inspection, maintenance and service in-

structions may cause personal injury or death.

NOTICE

Ensure that all adjustments and repairs that are

carried out to the fuel system are performed by

authorised personnel that have the correct train-

ing.

Before begining ANY work on the fuel system, re-

fer to Operation and Maintenance Manual, “Gen-

eral Hazard Information and High Pressure Fuel

Lines” for safety information.

Refer to System Operation, Testing and Adjusting,

“Cleanliness of Fuel System Components” for de-

tailed information on the standards of cleanliness

that must be observed during ALL work on the fu-

el system.

1.

If the engine is equipped with a cover over the fuel

system this will need to be removed.

g01341712

Illustration 342

1.

2.

Slide locking tab (1) into the unlocked position.

3.

Disconnect harness assembly (2) from fuel

pressure sensor (3).

4.

Place a suitable container below fuel pressure

sensor (3) in order to catch any fuel that might

be spilled.

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов