manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 129 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 129

KENR6932

129

Disassembly and Assembly Section

g01340518

Illustration 259

4.

Use Tooling (B) to install lifters (1) to the cylinder

block. Ensure that used lifters are installed in the

correct location.

Note:

The lifters should be free to rotate.

5.

Repeat Steps 1 and 4 in order to install the

remaining lifters.

End By:

a.

Install the camshaft. Refer to Disassembly and

Assembly, “Camshaft - Remove and Install”.

b.

Install the engine oil pump. Refer to Disassembly

and Assembly, “Engine Oil Pump - Install”.

i02654455

Camshaft - Remove and Install

 

Removal Procedure

Start By:

a.

Remove the rockershaft and pushrods. Refer to

Disassembly and Assembly, “Rocker shaft and

Pushrod - Remove”.

b.

Remove the front housing. Refer to Disassembly

and Assembly, “Housing (Front) - Remove”.

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

1.

The engine should be mounted on a suitable

stand and placed in the inverted position.

g01340531

Illustration 260
Typical example

2.

Remove thrust washer (1) from the cylinder block.

Do not remove dowel (2) from the cylinder block

unless the dowel is damaged.

Note:

The thrust washer can have one or two slots

(X).

g01340532

Illustration 261

NOTICE

Do not damage the lobes or the bearings when the

camshaft is removed or installed.

3.

Carefully remove camshaft (3) from the cylinder

block.

4.

If necessary, remove key (4) from camshaft (3).

Installation Procedure

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов