NetApp AFF A700 Скачать руководство пользователя страница 573 | Manualshive

Страница: 573 / 1672

background image

If the impaired node is
displaying…

Then…

System prompt or password
prompt (enter system password)

Take over or halt the impaired node:

• For an HA pair, take over the impaired node from the healthy

node:

storage failover takeover -ofnode

impaired_node_name

When the impaired node shows Waiting for giveback…, press
Ctrl-C, and then respond

y

.

Option 3: Controller is in a two-node MetroCluster

To shut down the impaired node, you must determine the status of the node and, if
necessary, switch over the node so that the healthy node continues to serve data from
the impaired node storage.

About this task

• If you are using NetApp Storage Encryption, you must have reset the MSID using the instructions in the

"Returning SEDs to unprotected mode" section of

Administration overview with the CLI

• You must leave the power supplies turned on at the end of this procedure to provide power to the healthy

node.

Steps

1. Check the MetroCluster status to determine whether the impaired node has automatically switched over to

the healthy node:

metrocluster show

2. Depending on whether an automatic switchover has occurred, proceed according to the following table:

If the impaired node…

Then…

Has automatically switched over

Proceed to the next step.

Has not automatically switched
over

Perform a planned switchover operation from the healthy node:

metrocluster switchover

Has not automatically switched
over, you attempted switchover
with the

metrocluster

switchover

command, and the

switchover was vetoed

Review the veto messages and, if possible, resolve the issue and try
again. If you are unable to resolve the issue, contact technical
support.

3. Resynchronize the data aggregates by running the

metrocluster heal -phase aggregates

command from the surviving cluster.

570

«
...
571
572
573
574
575
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFF A700

Бренд: IBM Страницы: 46

Бренд: SIGNALCORE Страницы: 32

Бренд: Advantech Страницы: 22

Бренд: Advantech Страницы: 24

Бренд: Advantech Страницы: 26

Бренд: Advantech Страницы: 30

Бренд: Advantech Страницы: 22

Бренд: Advantech Страницы: 30

Бренд: Advantech Страницы: 28

AIMB-B1000 Series

Бренд: Advantech Страницы: 28

Бренд: Advantech Страницы: 42

Бренд: Advantech Страницы: 34

Бренд: Advantech Страницы: 36

Бренд: Advantech Страницы: 38

Бренд: Advantech Страницы: 36

Бренд: Advantech Страницы: 44

Бренд: Advantech Страницы: 40

Бренд: Advantech Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды