NetApp AFF A700 Скачать руководство пользователя страница 1359 | Manualshive

Страница: 1359 / 1672

background image

2. At the LOADER prompt, access the special drivers specifically designed for system-level diagnostics to

function properly:

boot_diags

3. Select

Scan System

from the displayed menu to enable running the diagnostics tests.

4. Select

Test system

from the displayed menu to run diagnostics tests.

5. Select the test or series of tests from the various sub-menus.

6. Proceed based on the result of the preceding step:

◦

If the test failed, correct the failure, and then rerun the test.

◦

If the test reported no failures, select Reboot from the menu to reboot the system.

Step 3: Switch back aggregates in a two-node MetroCluster configuration

After you have completed the FRU replacement in a two-node MetroCluster
configuration, you can perform the MetroCluster switchback operation. This returns the
configuration to its normal operating state, with the sync-source storage virtual machines
(SVMs) on the formerly impaired site now active and serving data from the local disk
pools.

This task only applies to two-node MetroCluster configurations.

Steps

1. Verify that all nodes are in the

enabled

state:

metrocluster node show

cluster_B::> metrocluster node show

DR Configuration DR
Group Cluster Node State Mirroring Mode
----- ------- -------------- -------------- ---------
--------------------
1 cluster_A
controller_A_1 configured enabled heal roots
completed
cluster_B
controller_B_1 configured enabled waiting for
switchback recovery
2 entries were displayed.

2. Verify that resynchronization is complete on all SVMs:

metrocluster vserver show

3. Verify that any automatic LIF migrations being performed by the healing operations were completed

successfully:

metrocluster check lif show

4. Perform the switchback by using the

metrocluster switchback

command from any node in the

surviving cluster.

5. Verify that the switchback operation has completed:

metrocluster show

The switchback operation is still running when a cluster is in the

waiting-for-switchback

state:

1356

«
...
1357
1358
1359
1360
1361
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFF A700

SC825MTQ-R700LPB

Бренд: Supermicro Страницы: 78

Бренд: FSR Страницы: 2

Бренд: National Instruments Страницы: 43

Бренд: Cobra Страницы: 64

Бренд: National Instruments Страницы: 9

Бренд: VXI Technology Страницы: 41

Бренд: Supra Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды