NetApp AFF A700 Скачать руководство пользователя страница 1061

Страница: 1061 / 1672

If your system is in…

Then perform these steps…

An HA pair

The controller module begins to boot as soon as it is fully seated in
the chassis. Be prepared to interrupt the boot process.

a. With the cam handle in the open position, firmly push the

controller module in until it meets the midplane and is fully seated,
and then close the cam handle to the locked position.

Do not use excessive force when sliding the
controller module into the chassis to avoid
damaging the connectors.

The controller begins to boot as soon as it is seated in the
chassis.

b. If you have not already done so, reinstall the cable management

device.

c. Bind the cables to the cable management device with the hook

and loop strap.

d. When you see the message

Press Ctrl-C for Boot Menu

press

Ctrl-C

to interrupt the boot process.

If you miss the prompt and the controller module
boots to ONTAP, enter

halt

, and then at the

LOADER prompt enter

boot_ontap

, press

Ctrl-

when prompted, and then boot to Maintenance

mode.

e. Select the option to boot to Maintenance mode from the displayed

menu.

1058

«
...
1059
1060
1061
1062
1063
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание AFF A700

Отзывы:

Похожие инструкции для AFF A700

Бренды по названию

Популярные бренды

NetApp AFF A700, Системная документация

Результаты поиска

Содержание AFF A700

Отзывы:

Похожие инструкции для AFF A700

Бренды по названию

Популярные бренды