NetApp AFF A700 Скачать руководство пользователя страница 1231

Страница: 1231 / 1672

Step 3: Remove the controller module

To replace the chassis, you must remove the controller module or modules from the old
chassis.

1. Loosen the hook and loop strap binding the cables to the cable management device, and then unplug the

system cables and SFPs (if needed) from the controller module, keeping track of where the cables were
connected.

Leave the cables in the cable management device so that when you reinstall the cable management
device, the cables are organized.

2. Remove and set aside the cable management devices from the left and right sides of the controller module.

3. Loosen the thumbscrew on the cam handle on the controller module.

Thumbscrew

Cam handle

4. Pull the cam handle downward and begin to slide the controller module out of the chassis.

Make sure that you support the bottom of the controller module as you slide it out of the chassis.

5. Set the controller module aside in a safe place, and repeat these steps if you have another controller

module in the chassis.

1228

«
...
1229
1230
1231
1232
1233
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание AFF A700

Отзывы:

Похожие инструкции для AFF A700

Бренды по названию

Популярные бренды

NetApp AFF A700, Системная документация

Результаты поиска

Содержание AFF A700

Отзывы:

Похожие инструкции для AFF A700

Бренды по названию

Популярные бренды