NetApp AFF A700 Скачать руководство пользователя страница 1533

Страница: 1533 / 1672

If your HA pair is running…

Then…

A version of ONTAP 9.6

i. Reconfigure the RoCE capable ports for networking use, on the

first controller module:

storage port disable -node

node name

-port

port name

You must run this command for each port you are
reconfiguring.

ii. Reboot the controller module to make the port changes take

effect:

system node reboot -node

node name

-reason

reason

for the reboot

The reboot must complete before you proceed to
the next step. The reboot can take up to 15
minutes.

iii. Reconfigure the ports on the second controller module, by

repeating the first step.

iv. Reboot the second controller to make the port changes take

effect, by repeating the second step.

v. Go to substep 8c to verify all port changes.

c. Verify that the non-dedicated ports of both controller modules are reconfigured for networking use:

storage port show

You can enter the command on either controller module.

If your HA pair is running ONTAP 9.8 or later, the non-dedicated ports display

network

in the

Mode

column.

If your HA pair is running ONTAP 9.7 or 9.6, the non-dedicated ports, which display

false

in the

Dedicated?`

column, also display

disabled

in the

State

column.

Replace an NSM module - NS224 shelves

You can replace an impaired NVMe shelf module (NSM) nondisruptively in an NS224
drive shelf that is powered on, and while I/O is in progress.

Before you begin

• The shelf’s partner NSM module must be up and running, and be cabled correctly so that your shelf

maintains connectivity when you remove the failed NSM module.

NetApp Downloads: Config Advisor

• All other components in the system must be functioning properly.

About this task

1530

«
...
1531
1532
1533
1534
1535
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание AFF A700

Отзывы:

Похожие инструкции для AFF A700

Бренды по названию

Популярные бренды

NetApp AFF A700, Системная документация

Результаты поиска

Содержание AFF A700

Отзывы:

Похожие инструкции для AFF A700

Бренды по названию

Популярные бренды