NetApp AFF A700 Скачать руководство пользователя страница 1426 | Manualshive

Страница: 1426 / 1672

background image

c. Rotate the riser locking latch on the left side of the riser up and toward air duct.

The riser raises up slightly from the controller module.

d. Lift the riser up, and then set it aside on a stable, flat surface.

2. Replace the mezzanine card:

a. Remove any QSFP or SFP modules from the card.

b. Loosen the thumbscrews on the mezzanine card, and gently lift the card directly out of the socket and

set it aside.

c. Align the replacement mezzanine card over the socket and the guide pins and gently push the card into

the socket.

d. Tighten the thumbscrews on the mezzanine card.

3. Reinstall the riser:

a. Align the riser with the pins to the side of the riser socket, lower the riser down on the pins.

b. Push the riser squarely into the socket on the motherboard.

c. Rotate the latch down flush with the sheet metal on the riser.

Step 5: Install the controller module

After you have replaced the component in the controller module, you must re-install the
controller module into the chassis, and then boot it to Maintenance mode.

You can use the following animation, illustration, or the written steps to install the controller module in the
chassis.

Installing the controller module

Steps

1. If you have not already done so, close the air duct.

2. Align the end of the controller module with the opening in the chassis, and then gently push the controller

1423

«
...
1424
1425
1426
1427
1428
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFF A700

SnapServer NAS N2000

Бренд: Overland Storage Страницы: 4

Бренд: Juniper Страницы: 45

Бренд: Crestron Страницы: 12

Бренд: 3Com Страницы: 2

Бренд: abaco systems Страницы: 9

Бренд: Cisco Страницы: 24

AS5350 - Universal Access Server

Бренд: Cisco Страницы: 262

Бренд: National Instruments Страницы: 64

Бренд: HPE Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды