NetApp AFF A700 Скачать руководство пользователя страница 498

Страница: 498 / 1672

Press blue button

Rotate boot media up and remove from socket

a. Press the blue button at the end of the boot media until the lip on the boot media clears the blue button.

b. Rotate the boot media up and gently pull the boot media out of the socket.

3. Align the edges of the replacement boot media with the boot media socket, and then gently push it into the

socket.

4. Check the boot media to make sure that it is seated squarely and completely in the socket.

If necessary, remove the boot media and reseat it into the socket.

5. Lock the boot media in place:

a. Rotate the boot media down toward the motherboard.

b. Placing a finger at the end of the boot media by the blue button, push down on the boot media end to

engage the blue locking button.

c. While pushing down on the boot media, lift the blue locking button to lock the boot media in place.

6. Close the air duct.

495

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание AFF A700

Отзывы:

Похожие инструкции для AFF A700

Бренды по названию

Популярные бренды

NetApp AFF A700, Системная документация

Результаты поиска

Содержание AFF A700

Отзывы:

Похожие инструкции для AFF A700

Бренды по названию

Популярные бренды