NetApp AFF A700 Скачать руководство пользователя страница 1058 | Manualshive

Страница: 1058 / 1672

background image

Step 4: Move the DIMMs

To move the DIMMs, you must follow the directions to locate and move them from the old
controller module into the replacement controller module.

You must have the new controller module ready so that you can move the DIMMs directly from the impaired
controller module to the corresponding slots in the replacement controller module.

Steps

1. Locate the DIMMs on your controller module.

2. Note the orientation of the DIMM in the socket so that you can insert the DIMM in the replacement

controller module in the proper orientation.

3. Eject the DIMM from its slot by slowly pushing apart the two DIMM ejector tabs on either side of the DIMM,

and then slide the DIMM out of the slot.

Carefully hold the DIMM by the edges to avoid pressure on the components on the DIMM
circuit board.

The number and placement of system DIMMs depends on the model of your system.

The following illustration shows the location of system DIMMs:

4. Repeat these steps to remove additional DIMMs as needed.

5. Verify that the NVMEM battery is not plugged into the new controller module.

6. Locate the slot where you are installing the DIMM.

7. Make sure that the DIMM ejector tabs on the connector are in the open position, and then insert the DIMM

squarely into the slot.

The DIMM fits tightly in the slot, but should go in easily. If not, realign the DIMM with the slot and reinsert it.

1055

«
...
1056
1057
1058
1059
1060
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFF A700

Бренд: National Instruments Страницы: 4

NG4access ODF Platform Value-Added Module

Бренд: CommScope Страницы: 30

Бренд: Orban Страницы: 1

Бренд: Thermaltake Страницы: 12

Бренд: Thermaltake Страницы: 20

Бренд: TYAN Страницы: 76

Бренд: ADC Страницы: 34

Бренд: Keysight Technologies Страницы: 20

Бренд: Keysight Technologies Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды