NetApp AFF A700 Скачать руководство пользователя страница 728 | Manualshive

Страница: 728 / 1672

background image

node1_siteA::> metrocluster node show -fields configuration-state

dr-group-id cluster node configuration-state
----------- ---------------------- --------------
-------------------
1 node1_siteA node1mcc-001 configured
1 node1_siteA node1mcc-002 configured
1 node1_siteB node1mcc-003 configured
1 node1_siteB node1mcc-004 configured

4 entries were displayed.

11. Verify the operation of the MetroCluster configuration in Data ONTAP:

a. Check for any health alerts on both clusters:

system health alert show

b. Confirm that the MetroCluster is configured and in normal mode:

metrocluster show

c. Perform a MetroCluster check:

metrocluster check run

d. Display the results of the MetroCluster check:

metrocluster check show

e. Run Config Advisor. Go to the Config Advisor page on the NetApp Support Site at

support.netapp.com/NOW/download/tools/config_advisor/

After running Config Advisor, review the tool’s output and follow the recommendations in the
output to address any issues discovered.

12. Simulate a switchover operation:

a. From any node’s prompt, change to the advanced privilege level:

set -privilege advanced

You need to respond with

y

when prompted to continue into advanced mode and see the

advanced mode prompt (*>).

b. Perform the switchback operation with the -simulate parameter:

metrocluster switchover

-simulate

c. Return to the admin privilege level:

set -privilege admin

Step 6: Restore Storage and Volume Encryption functionality

After replacing the controller module or NVRAM module for a storage system that you
previously configured to use Storage or Volume Encryption, you must perform additional
steps to provide uninterrupted Encryption functionality. You can skip this task on storage
systems that do not have Storage or Volume Encryption enabled.

Step

1. Restore Storage or Volume Encryption functionality by using the appropriate procedure in

Encryption overview with the CLI

Use one of the following procedures, depending on whether you are using onboard or external key

725

«
...
726
727
728
729
730
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFF A700

Бренд: Crestron Страницы: 34

Supero SC933E1-R760B

Бренд: Supermicro Страницы: 84

Supero SC933 Series

Бренд: Supermicro Страницы: 84

EasyNote V Series

Бренд: Packard Bell Страницы: 27

Бренд: IEI Technology Страницы: 8

Бренд: Orban Страницы: 1

RM16M - Versatile Rack Mounting Chassis

Бренд: Telenetics Страницы: 49

VelocityKVM T-4200 Series

Бренд: Thinklogical Страницы: 23

Бренд: MicroNet Страницы: 7

Бренд: National Instruments Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды