NetApp AFF A700 Скачать руководство пользователя страница 557 | Manualshive

Страница: 557 / 1672

background image

1. Open the air duct:

a. Press the locking tabs on the sides of the air duct in toward the middle of the controller module.

b. Slide the air duct toward the back of the controller module, and then rotate it upward to its completely

open position.

2. Locate the NVDIMM battery in the controller module.

3. Locate the battery plug and squeeze the clip on the face of the battery plug to release the plug from the

socket, and then unplug the battery cable from the socket.

4. Grasp the battery and press the blue locking tab marked PUSH, and then lift the battery out of the holder

and controller module.

5. Remove the replacement battery from its package.

6. Align the battery module with the opening for the battery, and then gently push the battery into slot until it

locks into place.

7. Plug the battery plug back into the controller module, and then close the air duct.

Step 4: Install the controller module

After you have replaced the component in the controller module, you must re-install the
controller module into the chassis, and then boot it to Maintenance mode.

You can use the following animation, illustration, or the written steps to install the controller module in the
chassis.

Installing the controller module

1. If you have not already done so, close the air duct.

2. Align the end of the controller module with the opening in the chassis, and then gently push the controller

module halfway into the system.

Do not completely insert the controller module in the chassis until instructed to do so.

554

«
...
555
556
557
558
559
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFF A700

Бренд: NI Страницы: 11

Бренд: H&S Страницы: 28

Бренд: Salvo Страницы: 19

Бренд: Supero Страницы: 26

Бренд: Supero Страницы: 42

Бренд: Supero Страницы: 46

Бренд: Lantronix Страницы: 36

Бренд: Fractal Страницы: 42

Бренд: Philips Страницы: 87

Бренд: Rosewill Страницы: 8

Бренд: Rosewill Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды