NetApp AFF A700 Скачать руководство пользователя страница 567 | Manualshive

Страница: 567 / 1672

background image

2. Eject the NVDIMM from its slot by slowly pushing apart the two NVDIMM ejector tabs on either side of the

NVDIMM, and then slide the NVDIMM out of the socket and set it aside.

Carefully hold the NVDIMM by the edges to avoid pressure on the components on the
NVDIMM circuit board.

3. Remove the replacement NVDIMM from the antistatic shipping bag, hold the NVDIMM by the corners, and

then align it to the slot.

The notch among the pins on the NVDIMM should line up with the tab in the socket.

4. Locate the slot where you are installing the NVDIMM.

5. Insert the NVDIMM squarely into the slot.

The NVDIMM fits tightly in the slot, but should go in easily. If not, realign the NVDIMM with the slot and
reinsert it.

Visually inspect the NVDIMM to verify that it is evenly aligned and fully inserted into the slot.

6. Push carefully, but firmly, on the top edge of the NVDIMM until the ejector tabs snap into place over the

notches at the ends of the NVDIMM.

7. Close the air duct.

Step 4: Install the controller module

After you have replaced the component in the controller module, you must re-install the
controller module into the chassis, and then boot it to Maintenance mode.

You can use the following animation, illustration, or the written steps to install the controller module in the
chassis.

Installing the controller module

564

«
...
565
566
567
568
569
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFF A700

Бренд: National Instruments Страницы: 23

Бренд: CommScope Страницы: 25

Бренд: Gigabyte Страницы: 12

Бренд: Merging Страницы: 29

Бренд: Supero Страницы: 60

Бренд: Supero Страницы: 28

Бренд: Supero Страницы: 28

Бренд: Supero Страницы: 13

Бренд: Supero Страницы: 67

Бренд: Supero Страницы: 61

Бренд: Supero Страницы: 30

Бренд: Supero Страницы: 124

Бренд: Supero Страницы: 97

SC847BE1C series

Бренд: Supero Страницы: 116

Бренд: Supero Страницы: 82

SC847A-R1400LPB

Бренд: Supero Страницы: 120

Бренд: Supero Страницы: 54

Бренд: Supero Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды