NetApp AFF A700 Скачать руководство пользователя страница 1133 | Manualshive

Страница: 1133 / 1672

background image

If the impaired node is
displaying…

Then…

System prompt or password
prompt (enter system password)

Take over or halt the impaired node:

• For an HA pair, take over the impaired node from the healthy

node:

storage failover takeover -ofnode

impaired_node_name

When the impaired node shows Waiting for giveback…, press
Ctrl-C, and then respond

y

.

Move the controller module hardware - FAS500f

To replace the controller module hardware, you must remove the impaired node, move
FRU components to the replacement controller module, install the replacement controller
module in the chassis, and then boot the system to Maintenance mode.

Step 1: Remove the controller module

You must remove the controller module from the chassis when you replace a component
inside the controller module.

Make sure that you label the cables so that you know where they came from.

You can use the following video or the tabulated steps to replace a controller module:

Replacing a controller module

1. If you are not already grounded, properly ground yourself.

2. Unplug the controller module power supplies from the source.

3. Release the power cable retainers, and then unplug the cables from the power supplies.

4. Insert your forefinger into the latching mechanism on either side of the controller module, press the lever

with your thumb, and gently pull the controller a few inches out of the chassis.

If you have difficulty removing the controller module, place your index fingers through the
finger holes from the inside (by crossing your arms)

1130

«
...
1131
1132
1133
1134
1135
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFF A700

Бренд: Fujitsu Страницы: 12

Бренд: Fujitsu Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды