NetApp AFF A700 Скачать руководство пользователя страница 932 | Manualshive

Страница: 932 / 1672

background image

a. Firmly push the controller module into the chassis until it meets the midplane and is fully seated.

The locking latches rise when the controller module is fully seated.

Do not use excessive force when sliding the controller module into the chassis to avoid
damaging the connectors.

The controller module begins to boot as soon as it is fully seated in the chassis.

b. Rotate the locking latches upward, tilting them so that they clear the locking pins, and then lower them

into the locked position.

c. If you have not already done so, reinstall the cable management device.

6. Return the node to normal operation by giving back its storage:

storage failover giveback

-ofnode

impaired_node_name

7. If automatic giveback was disabled, reenable it:

storage failover modify -node local -auto

-giveback true

Step 5: Return the failed part to NetApp

After you replace the part, you can return the failed part to NetApp, as described in the
RMA instructions shipped with the kit. Contact technical support at

, 888-

463-8277 (North America), 00-800-44-638277 (Europe), or +800-800-80-800
(Asia/Pacific) if you need the RMA number or additional help with the replacement
procedure.

Replace a power supply - AFF A800

Replacing a power supply involves disconnecting the target power supply (PSU) from the
power source, unplugging the power cable, removing the old PSU and installing the
replacement PSU, and then reconnecting it to the power source.

• The power supplies are redundant and hot-swappable.

• This procedure is written for replacing one power supply at a time.

It is a best practice to replace the power supply within two minutes of removing it from the
chassis. The system continues to function, but ONTAP sends messages to the console
about the degraded power supply until the power supply is replaced.

1. If you are not already grounded, properly ground yourself.

2. Identify the power supply you want to replace, based on console error messages or through the red

Fault LED on the power supply.

3. Disconnect the power supply:

a. Open the power cable retainer, and then unplug the power cable from the power supply.

b. Unplug the power cable from the power source.

4. Rotate the cam handle such that it can be used to pull power supply out of the controller module while

pressing the locking tab.

929

«
...
930
931
932
933
934
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFF A700

Бренд: Mitsubishi Electric Страницы: 180

Бренд: Quantum Страницы: 32

FlexPoint LMC200A-2PS-DC

Бренд: Black Box Страницы: 4

Бренд: IEI Technology Страницы: 8

Бренд: Fujitsu Страницы: 12

Бренд: Fujitsu Страницы: 29

Бренд: Bay Networks Страницы: 64

Бренд: Wyrestorm Страницы: 26

Бренд: Corsair Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды