NetApp AFF A700 Скачать руководство пользователя страница 1539 | Manualshive

Страница: 1539 / 1672

background image

Before you begin

• The shelf’s partner NSM module must be up and running, and be cabled correctly so that your shelf

maintains connectivity when you remove the NSM module with the failed FRU (target NSM module).

NetApp Downloads: Config Advisor

• All other components in the system must be functioning properly.

About this task

• Allow at least 70 seconds between removal and installation of the NVMe shelf module (NSM).

This allows enough time for ONTAP to process the NSM removal event.

•

Best practice:

The best practice is to have current versions of NVMe shelf module (NSM) firmware and

drive firmware on your system before replacing FRU components.

Do not revert firmware to a version that does not support your shelf and its components.

NetApp Downloads: Disk Shelf Firmware

NetApp Downloads: Disk Drive Firmware

• If needed, you can turn on the shelf’s location (blue) LEDs to aid in physically locating the affected shelf:

storage shelf location-led modify -shelf-name

shelf_name

-led-status on

If you do not know the

shelf_name

of the affected shelf, run the

storage shelf show

command.

A shelf has three location LEDs: one on the operator display panel and one on each NSM module.
Location LEDs remain illuminated for 30 minutes. You can turn them off by entering the same command,
but using the

off

option.

• When you unpack the replacement RTC battery, save all packing materials for use when you return the

failed RTC battery.

If you need the RMA number or additional help with the replacement procedure, contact technical support
at

, 888-463-8277 (North America), 00-800-44-638277 (Europe), or +800-800-80-800

(Asia/Pacific).

• You can use the following video or the written steps to replace an RTC battery.

Replacing an RTC battery in an NS224 drive shelf

Steps

1. Properly ground yourself.

2. Disconnect the cabling from the NSM module that contains the FRU that you are replacing:

a. Disconnect the power cord from the power supply by opening the power cord retainer, and then unplug

the power cord from the power supply.

Power supplies do not have a power switch.

b. Disconnect the storage cabling from the NSM module ports.

Make a note of the NSM module ports that each cable is connected to. You reconnect the cables to the

1536

«
...
1537
1538
1539
1540
1541
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFF A700

Бренд: Kentrox Страницы: 306

Бренд: Racal Instruments Страницы: 185

Бренд: Magma Страницы: 52

Бренд: Fractal Страницы: 42

iConverter 8090-0

Бренд: OST Страницы: 12

Бренд: Wyrestorm Страницы: 26

Бренд: Jou Jye Страницы: 3

Бренд: CSN Страницы: 2

Бренд: Addonics Technologies Страницы: 2

Бренд: AIC Страницы: 24

Бренд: AIC Страницы: 27

Бренд: AIC Страницы: 25

Бренд: AIC Страницы: 25

Бренд: AIC Страницы: 25

Бренд: AIC Страницы: 31

Бренд: AIC Страницы: 34

Бренд: AIC Страницы: 36

Бренд: AIC Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды