NetApp AFF A700 Скачать руководство пользователя страница 305 | Manualshive

Страница: 305 / 1672

background image

You must perform a clean system shutdown before replacing the chassis to avoid losing
unwritten data in the nonvolatile memory (NVMEM). If the NVMEM LED is flashing, there is
content in the NVMEM that has not been saved to disk. You need to reboot the node and
start from the beginning of this procedure. If repeated attempts to cleanly shut down the
node fail, be aware that you might lose any data that was not saved to disk.

3. Where applicable, halt the second node to avoid a possible quorum error message in an HA pair

configuration:

system node halt -node second_node_name -ignore-quorum-warnings true

Option 2: Controllers are in a two-node MetroCluster configuration

To shut down the impaired node, you must determine the status of the node and, if
necessary, switch over the node so that the healthy node continues to serve data from
the impaired node storage.

About this task

• If you are using NetApp Storage Encryption, you must have reset the MSID using the instructions in the

"Returning SEDs to unprotected mode" section of

Administration overview with the CLI

• You must leave the power supplies turned on at the end of this procedure to provide power to the healthy

node.

Steps

1. Check the MetroCluster status to determine whether the impaired node has automatically switched over to

the healthy node:

metrocluster show

2. Depending on whether an automatic switchover has occurred, proceed according to the following table:

If the impaired node…

Then…

Has automatically switched over

Proceed to the next step.

Has not automatically switched
over

Perform a planned switchover operation from the healthy node:

metrocluster switchover

Has not automatically switched
over, you attempted switchover
with the

metrocluster

switchover

command, and the

switchover was vetoed

Review the veto messages and, if possible, resolve the issue and try
again. If you are unable to resolve the issue, contact technical
support.

3. Resynchronize the data aggregates by running the

metrocluster heal -phase aggregates

command from the surviving cluster.

controller_A_1::> metrocluster heal -phase aggregates
[Job 130] Job succeeded: Heal Aggregates is successful.

If the healing is vetoed, you have the option of reissuing the

metrocluster heal

command with the

-override-vetoes parameter. If you use this optional parameter, the system overrides any soft vetoes that
prevent the healing operation.

302

«
...
303
304
305
306
307
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFF A700

Бренд: REDCAT Страницы: 24

Бренд: Pitney Bowes Страницы: 336

VX1411A IntelliFrame VXIbus Mainframe

Бренд: Tektronix Страницы: 130

Бренд: Allied Telesis Страницы: 44

Sun Storage J4200

Бренд: Sun Microsystems Страницы: 112

Бренд: ETAS Страницы: 52

Бренд: NXP Semiconductors Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды