NetApp AFF A700 Скачать руководство пользователя страница 1619 | Manualshive

Страница: 1619 / 1672

background image

9. If you are replacing another disk drive, repeat Steps 3 through 8.

10. Verify the disk drive’s activity (green) LED is illuminated.

When the disk drive’s activity LED is solid green, it means the disk drive has power. When the disk drive’s
activity LED is blinking, it means the disk drive has power and I/O is in progress. If the disk drive firmware
is automatically updating, the LED will be blinking.

11. If you disabled automatic drive assignment in Step 1, manually assign disk ownership, and then reenable

automatic drive assignment if needed:

a. Display all unowned disks:

storage disk show -container-type unassigned

b. Assign each disk:

storage disk assign -disk

disk_name

-owner

owner_name

You can use the wildcard character to assign more than one disk at once.

c. Reenable automatic drive assignment if needed:

storage disk option modify -node

node_name

-autoassign on

You need to reenable automatic drive assignment on both controllers in an HA pair.

12. Return the failed part to NetApp, as described in the RMA instructions shipped with the kit.

Contact technical support at

, 888-463-8277 (North America), 00-800-44-638277 (Europe),

or +800-800-80-800 (Asia/Pacific) if you need the RMA number or additional help with the replacement
procedure.

Hot-swap a disk drive in a DS460C disk shelf - shelves with IOM12 modules

You can hot-swap a failed disk drive in a DS460C disk shelf.

Before you begin

• The replacement disk drive must be supported by the DS460C disk shelf.

NetApp Hardware Universe

• All other components in the system must be functioning properly; if not, contact technical support.

• The disk drive you are removing must be failed.

You can verify the disk drive is failed by running the

storage disk show -broken

command. The

failed disk drive appears in the list of failed disk drives. If it does not, you should wait, and run the
command again.

Depending on the disk drive type and capacity, it can take up to several hours for the disk
drive to appear in the list of failed disk drives.

• If you are replacing a self-encrypting disk (SED), you must follow the instructions for Replacing an SED in

the ONTAP documentation for your version of ONTAP.

Instructions in the ONTAP documentation describe additional steps you must perform before and after
replacing an SED.

NetApp encryption overview with the CLI

1616

«
...
1617
1618
1619
1620
1621
...
»

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFF A700

Бренд: National Instruments Страницы: 14

Бренд: InWin Страницы: 10

Бренд: Cabletron Systems Страницы: 2

Бренд: Solid State Logic Страницы: 52

Бренд: Viglen Страницы: 58

Бренд: Chassisworks Страницы: 106

Бренд: Fujitsu Страницы: 12

Бренд: Fujitsu Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды