NetApp AFF A700 Скачать руководство пользователя страница 989

Страница: 989 / 1672

If the system-level diagnostics
tests…

Then…

Were completed without any
failures

a. Clear the status logs:

sldiag device clearstatus

b. Verify that the log was cleared:

sldiag device status

The following default response is displayed:

SLDIAG: No log messages are present.

c. Exit Maintenance mode:

halt

The system displays the LOADER prompt.

You have completed system-level diagnostics.

Resulted in some test failures

Determine the cause of the problem.

a. Exit Maintenance mode:

halt

b. Perform a clean shutdown, and then disconnect the power

supplies.

c. Verify that you have observed all of the considerations identified

for running system-level diagnostics, that cables are securely
connected, and that hardware components are properly installed
in the storage system.

d. Reconnect the power supplies, and then power on the storage

system.

e. Rerun the system-level diagnostics test.

Recable the system and reassign disks - AFF C190

Continue the replacement procedure by recabling the storage and confirming disk
reassignment.

Step 1: Recable the system

After running diagnostics, you must recable the controller module’s storage and network
connections.

986

Содержание AFF A700









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание AFF A700

Отзывы:

Похожие инструкции для AFF A700

Бренды по названию

Популярные бренды

NetApp AFF A700, Системная документация

Результаты поиска

Содержание AFF A700

Отзывы:

Похожие инструкции для AFF A700

Бренды по названию

Популярные бренды