manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 1

 

 GridTime

™

 3000 Installation Manual

Overview

The GridTime 3000 is a rack mountable precision time server for digital substation applications. Its timing protocols
and ports are enabled through license bundles (See 

4.  Licenses

 for a full list of all license bundles), allowing for

different functionality to be enabled as requirements change.

The GridTime 3000 has an extensive collection of different ports, including:

• Ten Ethernet ports (two RJ-45, eight SFP) on its front panel for Network Time Protocol (NTP) and Precision

Time Protocol (PTP) time synchronization

• Fifteen ports on its back panel for input of IRIG-B, and output of a range of legacy time and frequency signals
• An antenna connector on its back panel to utilize a GNSS reference.

The GridTime 3000 is suitable for use in synchronizing industrial control and supervisory control and data acquisition
(SCADA) equipment. It can provide time synchronization to many different devices simultaneously, such as Phasor
Measurement Units (PMUs), Protection Relays, Remote Telemetry Units (RTUs) and other Intelligent Electronic
Devices (IEDs) used in electrical substations and industrial control installations.

The GridTime 3000 is suitable for harsh electromagnetic environments as all its ports are electrically isolated. This
allows output wiring to feed out to operating areas in different earth potential zones without compromising site
earthing security. The isolation also protects the device from high voltage spikes.

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 1

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды