manualshive.com logo in svg

LS LSLV-iV5 Series, Руководство пользователя

Продукт LS LSLV-iV5 Series - это инновационная серия устройств, предлагающая высокое качество и надежность. Скачайте бесплатное руководство пользователя для данного продукта на manualshive.com, чтобы максимально эффективно использовать все его функции и возможности.

Поделиться
Скачать
background image

11. Option Devices 

 

 

11-3 

11.1.3 Encoder division output 

Only available when Encoder Division Output Option Card is installed. 

Sets the division ratio for monitoring the Encoder pulse signals.   

Code 

Address 

  LCD 

display 

Description 

Setting range 

Unit   

Factory 

setting 

PAR_32 

7320 

EncDiv Ratio  Encoder Pulse Output Division Rate 

1 ~ 1128 

 

1 

PAR_33 

7321 

EncDivFilter 

Encoder Division Output Filter 

0 ~ 15 

 

0 

Encoder division output option card outputs one pulse signal when input pulse number matches the value set in PAR_32. 

A/B pulse output follows input pulse  phase. The relationship between output of A, B pulse  follows  the  same as input 

pulse.

 

Division ration can be set within the range of 1 (1 output pulse per 1 input pulse) ~ 1/128(1 output pulse to 128 

input pulse).   

PAR_32  setting  range:  0001  ~  1128.  Division  ratio  cannot  be  set  higher  than  1  and  only  1  or  2  can  be  set  for 

numerator. The below is Division ratio calculation formula.   

N refers to the value from thousand (

0

000) and M refers to value less than thousand (0

000

) 

PAR_32 set value = N

1000 + M. 

 

Division ratio = (1+N)/M 

Setting range: N (0, 1), M (1 ~ 128) 

PAR_32 = [] [] [] [] 

 

 

When  PAR_32  setting  value  is  below  1000  (N=0),  a  numerator  value  becomes 1  and  when  above  1000 

(N=1),  a  numerator  value  becomes  2. For  example, if  PAR_32  is  set to 15, the  division  ratio  is  1/15  and  if 

1015, the ratio is 2/15. Division ratio is settable up to 1/128 and greater than 1 is not settable. Using Up key 

on  the  keypad  PAR_32  value  is  increased  and  increase  routine  is  1 

  2 

  3 

  4 

 

… 

  127 

 

128(Division  ratio:  1/128) 

  1002  (Division  ratio:  1) 

  1003 

 

… 

  1128  (Division  ratio:  1/64)  and 

decrease routine (using Down key on the keypad) is the same as increase routine. 

 

N  M 

Содержание LSLV-iV5 Series

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LSLV-iV5 Series

Danfoss VLT CDS302 Operating Instructions Manual preview
VLT CDS302
Бренд: Danfoss Страницы: 161
GU ELTRAL VA35 Assembly And Operating Instructions Manual preview
ELTRAL VA35
Бренд: GU Страницы: 13
Sony VGC-RB33G Vaio Service And Warranty Information preview
VGC-RB33G Vaio
Бренд: Sony Страницы: 1
Sony VGC-RB41P Vaio User Manual preview
VGC-RB41P Vaio
Бренд: Sony Страницы: 2
Sony VAIO VPCEB42FX Specifications preview
VAIO VPCEB42FX
Бренд: Sony Страницы: 2
Sony VAIO VPCEB47GM Specifications preview
VAIO VPCEB47GM
Бренд: Sony Страницы: 4
Sony VAIO VGN-SR240N Specifications preview
VAIO VGN-SR240N
Бренд: Sony Страницы: 2
Sony VAIO VGC-RB38G Service And Warranty Information preview
VAIO VGC-RB38G
Бренд: Sony Страницы: 1
Sony VAIO VGC-RB36G Service And Warranty Information preview
VAIO VGC-RB36G
Бренд: Sony Страницы: 1
Sony VAIO VGC-RB35G Service And Warranty Information preview
VAIO VGC-RB35G
Бренд: Sony Страницы: 1
Sony Vaio VGN-SR490J Specifications preview
Vaio VGN-SR490J
Бренд: Sony Страницы: 2
Sony PCG-K Series Replacement Instructions preview
PCG-K Series
Бренд: Sony Страницы: 2
Sony PCG-GRT Series Replacement Instructions preview
PCG-GRT Series
Бренд: Sony Страницы: 2
Sony DRX-120L User Manual preview
DRX-120L
Бренд: Sony Страницы: 2
Sony MO DISK DRIVE SMO-F551 Installation Manual preview
MO DISK DRIVE SMO-F551
Бренд: Sony Страницы: 31
Sony DRX-S70U-W Operating Instructions Manual preview
DRX-S70U-W
Бренд: Sony Страницы: 24
Sony RMO-S591 User Manual preview
RMO-S591
Бренд: Sony Страницы: 49
Sony MO DISK DRIVE SMO-F551 Technical Manual preview
MO DISK DRIVE SMO-F551
Бренд: Sony Страницы: 46

Бренды по названию

Популярные бренды

Загрузить еще бренды