Kikusui PAT160-25T, Руководство по эксплуатации

Страница: 173 / 218

PAT-T 4kW
9-3
9
Spec
ifica
tions
Output specifications
PAT20-200T PAT40-100T PAT60-67T PAT160-25T
Rating
O u tp u t po w er
three-phase inp u t mode 4 kW
single-phase inp u t mode 3 kW
O u tp u t voltage 20.00 V 40.00 V 60.00 V 160.0 V
O u tp u t c u rrent
*1
*1. In the single-phase inp u t mode, the o u tp u t c u rrent is limited to 75 % of the rating of three-phase inp u t mode.
200.0 A 100.0 A 67.0 A 25.0 A
Voltage
Preset range
*2
*2. The maxim u m preset voltage and c u rrent are u sed to determine constant voltage or constant c u rrent operation w hen
the activation point of the constant voltage or constant c u rrent operation is set to the rated o u tp u t voltage or c u rrent. It
does not g u arantee po w er s u pply to the load exceeding the rated o u tp u t voltage or c u rrent.
To establish a constant voltage operation at the activation point (rated o u tp u t voltage or c u rrent), set the o u tp u t c u rrent
(I Set) so that rated o u tp u t c u rrent < I Set
≤
maxim u m preset c u rrent.
Like w ise, to establish constant c u rrent operation, set the o u tp u t voltage (V Set) so that rate o u tp u t voltage < V Set
≤
maxim u m preset voltage.
0 % to 105 % of rtg
Setting acc u racy
*3
*3. The difference bet w een the act u al o u tp u t voltage or o u tp u t c u rrent and the preset val u e u nder constant voltage or
constant c u rrent operation.
± (0.2 % of rtg + 50 mV)
So u rce effect
*4
*4. O u tp u t voltage or o u tp u t c u rrent fl u ct u ation w ith respect to ±10 % fl u ct u ation of the nominal inp u t voltage u nder constant
voltage or c u rrent operation.
± (0.05 % of rtg + 5 mV)
Load effect
*5
*5. O u tp u t voltage or o u tp u t c u rrent fl u ct u ation w hen the o u tp u t voltage or o u tp u t c u rrent is set to the rated o u tp u t voltage
or c u rrent and the load is changed from rated load to no load u nder constant voltage or c u rrent operation.
± (0.1 % of rtg + 5 mV)
Transient response
*6
*6. The time it takes for the o u tp u t voltage fl u ct u ation to recover from o u tside 0.1 % + 10 mV of the o u tp u t voltage setting
to w ithin 0.1 % + 10 mV w hen the o u tp u t c u rrent is changed from 100 % to 50 % or 50 % to 100 % of the rated o u tp u t
c u rrent u nder constant voltage operation. The o u tp u t voltage w hen the o u tp u t c u rrent is 100 % is u sed as a reference.
5 ms
Ripple noise
(p-p)
*7
*7. When the meas u rement freq u ency band w idth is 10 Hz to 20 MHz.
100 mV 300 mV 350 mV
(rms)
* 8
* 8 . When the meas u rement freq u ency band w idth is 5 Hz to 1 MHz for the o u tp u t voltage from 10 % to 100 % of the rating.
10 mV 30 mV
Rise time (MAX)
*9
*9. The time it takes for the o u tp u t voltage to rise from 10 % to 90 % of the rating w hen the o u tp u t is t u rned on.
rated load 100 ms
no load 100 ms
Fall time (MAX)
*10
*10. The time it takes for the o u tp u t voltage to fall from 90 % to 10 % of the rating w hen the o u tp u t is t u rned off.
rated load 100 ms
no load 2000 ms
Temperat u re coefficient (MAX)
*11
*11. When the ambient temperat u re is w ithin the range of 0 ° C to 50 ° C.
100 ppm/ ° C (d u ring external control)
C u rrent
Preset range
*2
three-phase inp u t mode 0 % to 105 % of rtg
single-phase inp u t mode 0 % to 105 % of rtg x 75 %
Setting acc u racy
*3
± (0.5 % of rtg + 50 mA)
So u rce effect
*4
± (0.1 % of rtg + 30 mA)
Load effect
*5
± (0.2 % of rtg +30 mA)
Ripple noise (rms)
* 8
400 mA 300 mA 250 mA 200 mA
Temperat u re coefficient (TYP)
*11
200 ppm/ ° C (d u ring external control)