9-2
PAT-T 4kW
9.1
Specifications
Unless specified otherwise, the specifications are for the following settings and conditions.
•
The load is a pure resistance.
•
The warm-up time is 30 minutes (with current flowing).
•
After warm-up is complete, the PAT must be calibrated correctly according to the
procedures given in the operation manual in a 23 ° C ± 5 ° C environment.
•
TYP (typical) values do not guarantee the performance.
•
rtg:
Indicates the rated output.
•
rdng:
Indicates the reading.
•
Rated load and no load are defined as follows:
D
u
ring constant voltage operation (set the o
u
tp
u
t c
u
rrent at the rated voltage
o
u
tp
u
t greater than eq
u
al to the rated o
u
tp
u
t c
u
rrent)
Rated load:Refers to a load with a resistance that makes the current that flows when the rated
output voltage is applied to be 95 % to 100 % of the rated output current at the rated
output voltage.
No load:
Refers to a load through which no output current flows or an open output terminal
condition with no load connected.
D
u
ring constant c
u
rrent operation (set the o
u
tp
u
t voltage at the rated o
u
tp
u
t
c
u
rrent greater than eq
u
al to the rated o
u
tp
u
t voltage)
Rated load:Refers to a load with a resistance that makes the voltage drop when the rated output
current is supplied to be 95 % to 100 % of the maximum output voltage at the rated
output current.
The output voltage of the PAT including the voltage drop in the load cable must not
exceed the maximum output voltage at the rated output current.
No load:
Refers to a load with a resistance that makes the voltage drop when the rated output
current is supplied to be 10 % of the maximum output voltage or 1 V, whichever is
greater, at the rated output current.
AC input
PAT20-200T
PAT40-100T
PAT60-67T
PAT160-25T
N
ominal inp
u
t rating
200 V to 240 V, 50 Hz to 60 Hz
Inp
u
t voltage range
1
8
0 V to 250 V
Inp
u
t freq
u
ency range
47 Hz to 63 Hz
Inp
u
t phase
three-phase inp
u
t mode
Three-phase (at the rated load)
single-phase inp
u
t mode
Single-phase (at 3 kW)
Hold-
u
p time for po
w
er interr
u
ption (MI
N
)
20 ms or greater (at 50 % load), 10 ms or greater (at the rated load)
C
u
rrent
three-phase inp
u
t mode
17 A or less (at the rated load)
single-phase inp
u
t mode
22 A or less (at 3 kW)
Inr
u
sh c
u
rrent (MAX)
*1
*1.
Excl
u
des the charge c
u
rrent component that flo
w
s thro
u
gh the capacitor of the internal EMC filter circ
u
it
immediately after the POWER s
w
itch is t
u
rned on (
w
ithin approximately 1 ms).
50.0 A peak
Wattage (MAX)
three-phase inp
u
t mode
5 kVA (at the rated load)
single-phase inp
u
t mode
4 kVA (at 3 kW)
Po
w
er factor (TYP)
*2
*2.
inp
u
t voltage of 200 V, at the rated load.
0.95
Efficiency (MI
N
)
8
4.0 %
8
5.0 %
Содержание PAT160-25T
