Johnson Controls Bentel Security tyco ABS128M50, Руководство по установке

Страница: 69 / 132

+
Events that belong to the events group in the
Smart Actions options group, which have the
Only enabled in Events and Actions option
ENABLED, have this option empty and locked (see
“Smart Actions” for further information).
Vocal Numbers
7
If disabled, the event does NOT send
an SMS to the respective Telephone Number.
If ENABLED (default), the event sends the programmed
SMS message to the respective Telephone Number
(See the
Phonebook option group).
n
CENTRAL STATION ACTIONS
+
The communicator is disabled as long as there is a
PIN to default fault, i.e., no communication action
is performed even if programmed (see “EN50136”
in “System Options > EN50131/EN50136”).
The options described below are for reporting Events in
digital format to the Central Stations via PSTN, GSM,
GPRS and IP.
3
In order to comply with EN50131 Grade 3 stan-
dards, ONLY use the
ABS-IP IP Module to report
alarms: the integrated PTSN communicator and the
ABS-GSM GSM/GPRS Module CANNOT be used.
Telephone Enabled If this option is ENABLED the
event will be sent via PSTN/GSM to the numbers se-
lected in the
Digital Numbers option.
Default: see Table 10.
Restore If disabled, the event does NOT send codes,
via PSTN/GSM, when it ends.
If ENABLED (default), when the event ends, it sends
the programmed codes via PSTN/GSM (see
Contact
ID and Restore SIA Identifier ).
Call All If this option is ENABLED (default), the Control
Panel will call ALL the phone numbers for the event
(see
Digital Numbers ).
If this option is disabled, the Control Panel will call the
phone numbers for the event (see
Digital Numbers )
until a call ends successfully: the other event’s numbers
will NOT be called.
Digital Numbers If disabled, the control Panel does
NOT send the event to the respective Telephone Number.
If ENABLED (default), the Control Panel sends the
event to the respective Telephone Number (See the
Phonebook option group).
+
This column ONLY shows the Digital Number
telephone numbers that are NOT empty i.e. are
made up of at least one digit (see
Number and
Type in the Phonebook options group). This col-
umn is NOT displayed if there is no telephone num-
ber with these characteristics.
Receiver If enabled, the control panel transmits the
event via GPRS (the GSM module is required) and/or
via IP (the IP module is required) to a Sur-Gard
SYSTEM
I , II o III receiver, as configured in the GSM
and IP option groups on the basis of the Receiver
Channel Priority option setting (see the System Op-
tions > General options group).
Default: Disabled.
+
The Receiver is disabled when the option Re-
ceiver for Digital Call Failed is enabled.
Send Restore Over receiver If disabled, the event
does NOT send codes, via GPRS and via IP, when it
ends.
If ENABLED (default), when the event ends, it sends
the programmed codes via GPRS and/or IP (see
Con-
tact ID and Restore SIA Identifier ).
Receiver for Digital Call Failed If enabled, the con-
trol panel sends the event via GPRS and/or via IP,
ONLY if it fails to send it via PSTN/GSM.
Default: Disabled.
+
The option Receiver for Digital Call Failed is dis-
abled when the Receiver option is enabled.
Digital Call for Receiver Failed If enabled, the con-
trol panel will send the event via PSTN/GSM when it
fails to send to the receiver via GPRS/IP.
Default: disabled.
+
The Digital Call for Receiver Failed option is
blocked if the Receiver option is disabled or if the
Receiver for Digital Call Failed option is enabled.
Contact ID Enter the Contact ID Reporting Code for
the event: the control panel sends the code, preceded
by the digit
1 when the event OCCURS and by the digit
3 when the event ENDS.
+
The control panel sends the Contact ID reporting
code when the event ends ONLY if the option
Re-
store is enabled.
Event SIA Identifier Enter the SIA Reporting Code
that the Control Panel must send when the relative
event
OCCURS .
Restore SIA Identifier Enter the SIA Reporting Code
that the Control Panel must send when the relative
event
ENDS .
+
This option is not available for spot events.
+
The control panel sends the SIA reporting code
when the event ends ONLY if the option
Restore is
enabled.
+
00 and 000 mean that the event will be not commu-
nicated.
ABSOLUTA Plus PROGRAMMING FROM THE PC 69